PROTEK 6510

Protek 6510 100MHz Oscilloscope Features: Four traces may be simultaneously displayed in ALT-sweep Five vertical display modes: CH1, CH2, Dual, Add, Subtract Vertical mode triggering for displaying 2 unrelated signals Trigger hold-off circuit for synchronizing complex waveforms Sweep speeds to 2nS/ Div 12kV acceleration voltage for bright displays of low duty cycle signals Z axis input TV Synchronization for either line or field patterns 20MHz bandwidth limit switch for triggering signals in a noisy environment Specifications Vertical Amplifier ( CH 1 and CH 2) Sensitivity 5 mV/ Div to 5 V/ Div in 7 calibrated steps, ( X5 Mag 1mV/ Div to 1 V/ Div) Accuracy ± 3% ( ± 5% in X5 Mag) Bandwidth ( -3dB) DC to 100MHz Rise Time £ 3.5 ns, X5 Mag: 20MHz Bandwidth: £ 17 ns Input Impedance 1MW + 25 pF Input Coupling AC-Gnd-DC Invert Channel CH2 Display Modes CH1, CH2, Add, Subtract, Dual ( Alt/ Chop) Maximum Input Voltage 400V ( DC or AC peak) CH1 Signal Output 20mV into 50W Horizontal Sweep Timebase A - Sweep Time 50ns/ Div to 0.2 s/ Div in 21 calibrated steps ( 1-2-5) Timebase A - X10 Mag 5ns/ Div to 20ms/ Div Timebase A - Accuracy ± 3% ( ± 5% in X10 Mag) Timebase A - Hold Off Continuously adjustable to > 2X sweep time Timebase B - Sweep Time 50ns/ Div to 10µ s/ Div in 8 steps ( 1-2-5) Timebase B - Accuracy ± 3% Timebase B - Delay Time Continuously variable from 0.2µ s to 2s Timebase B - Delay Modes Continuous or triggered Timebase B - Sweep Displays A, B, A alt B, B triggered, X-Y X-Y Mode CH1-X axis, CH2-Y axis Sensitivity Same as CH1 vertical amplifier Bandwidth ( X-axis) DC to 2MHz Phase Error £ 3° DC to 10kHz Triggering Trigger Modes Auto, Normal, TV-V, TV-L Source Int. CH2, line ext. Coupling AC Slope Positive or negative Trigger Sensitivity Int ( DC to 10MHz) : 0.5 Div Int ( 10MHz to 100MHz) : 1.5 Div Ext ( DC to 10MHz) : 200mV Ext ( 10MHz to 100MHz) : 500mV TV ( Int) : 1 Div Min TV ( Ext) : 1V P-P External Trigger Input Impedance: 1MW + 20 pF Maximum Input Volts: 400V DC or AC peak Z Axis Modulation Sensitivity ± 5V P-P Intensity increases with a negative going voltage input Bandwidth ( -3dB) DC to 2MHz Input Impedance Approx. 2 KW Calibrator Signal Voltage 0.5V ± 3% P-P 1kHz Square Wave Duty Cycle Approx. 50% CRT Type 6 " rectangular CRT with internal graticule. ( 1 Div = 1cm) Acceleration Voltage 12 kV General Specification Power Requirements AC Input Voltage: 100V, 120V, 220V, 240V selectable Frequency 50/ 60Hz Power Consumption 55W Operating Temperature 0 to 40° C at 35% to 85% relative humidity DIMensions 5.25 " H × 12.67 " W × 14.5 " D Weight 24 lbs. Supplied Accessories Manual, 1 AC Power cord, ( 2) X10 Probes